|This bookcase is a free standing bookcase with all the charm and simple beauty of mission style furniture.
This beautiful piece of mission furniture can be made at a very moderate cost.
Quarter sawed oak is the best wood to use, as it is easy to work and looks best when finished. Order the stock from the mill ready cut to length, squared and sanded.
You will need:
- 1 top, 3/4 by 15 by 31-1/4 in., hard wood, S-1-S.
- 1 top back board, 3/4 by 4 by 30-1/4 in., hard wood, S-1-S.
- 2 sides, 3/4 by 14 by 50 in., hard wood, S-1-S.
- 1 bottom, 3/4 by 14 by 28-3/4 in., hard wood, S-1-S.
- 1 bottom rail, 3/4 by 4 by 28-3/4 in., hard wood, S-1-S.
- 1 center piece, 3/4 by 2 by 45-3/4 in., hard wood, S-2-S.
- 4 door sides, 3/4 by 1-1/2 by 45-1/4 in., hard wood, S-2-S.
- 4 door ends, 3/4 by 1-1/2 by 14 in., hard wood, S-2-S.
- 4 pieces door lattice, 1/2 by 1/2 by 12-1/2 in., hard wood.
- 4 pieces door lattice, 1/2 by 1/2 by 7 in., hard wood.
- 2 bottom cleats, 1-1/4 by 1-1/4 by 13 in., soft wood.
- 2 top cleats, 1 by 1 by 12-1/2 in., soft wood.
- 3 shelves, 1/2 by 12 by 28-1/2 in., soft wood.
- 12 pieces backing, 3/8 by 4 by 29-3/4 in., soft wood.
- 4 hinges.
- 2 door handles.
Begin with the sides by cutting them so they will pair up all right. The front edges are rounded while the back edges are rabbeted on the inside as deep as the backing to be used. The bottoms are cut as shown in the sketch. Holes about 1/2 in. deep should be bored on the inside at the proper places for the wooden pegs which hold up the shelves.
Details of Bookcase Construction
The top and bottom boards should have the front edges rounded and sanded the same as the sides. The top board is sanded on one side only and care should be taken to get the best side up.
Now cut and fit the top back board. This is fastened to the top by means of screws. Screw two cleats to each of the sides as shown and by running screws through these into the top and bottom boards the frame is completed.
The backing which can be made of some cheap lumber is now put on. Next put in the center upright piece between the doors by means of a tenon and mortise at the top and nail at the bottom. The front edge should be rounded and the edge and sides sanded. Cut and fit the bottom rail as shown. It is fastened to the frame by means of cleats on the back side.
The doors are put together by means of a tenon and mortise. They should be rabbeted for the lattice work and the glass. This lattice work can be omitted and leaded glass put in its place which is very becoming to this kind of work.
When the case is completed it must be carefully gone over with sandpaper before any finish is applied.
A mission stain is suitable for work of this kind, but it can also be finished in "golden oak" which is done in the following manner: First put on a golden oak stain and after it has dried for about 2 hours, apply the filler. Let this dry about 10 minutes then rub off with an old rag. Then go over the case again with some very fine sandpaper and after seeing that all parts are free from dust and dirt the varnish can be applied. Three coats of varnish will give a beautiful glossy finish.